Spectra-precision Survey Pro v3.80 Recon iPAQ Reference Manual Manual de usuario Pagina 110
- Pagina / 261
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Survey Pro Reference Manual
R-104
Solar Observation
The Solar Observation screen is used to compute the azimuth to an
arbitrary backsight based on the position of a celestial body; typically
the sun.
WARNING!
Direct viewing of the sun
without a proper filter will cause serious eye
damage. Pointing a total station directly toward the
sun without a solar filter can also damage the EDM
components.
Find Azimuth Using Ephemeris Data
: select this method
if you plan to enter data from an ephemeris.
Find Azimuth Using Date and Time
: select this method if
you do not plan to use an ephemeris.
Note: The fields within the Solar Observations
screen
will vary depending on the method selected above. All of
the fields from each method are described below.
: located at the top of the screen, is a shortcut
to the Date/Time Settings screen (Page R-39).
Lat.
/
Long.
: is the latitude and longitude of the total
station. These values can be scaled from a map, such as
a U.S.G.S. 7.5-minute quadrangle sheet or collected with
a handheld GPS unit.
Aim
: selects the portion of the celestial body that where
you intend to aim. You can select
Left Edge of Center
,
Center
, or
Right Edge of Center
.
- SURVEY PRO 1
- Table of Contents 3
- Welcome 7
- Main Menu 9
- File Menu 11
- Open / New 12
- New Job 13
- Save As 17
- Import Coordinates 18
- Import *.JOB Coordinates 19
- Import *.CR5 Coordinates 20
- Import *.TXT Coordinates 20
- Export Coordinates 23
- Export Old *.JOB Coordinates 24
- Export *.CR5 Coordinates 24
- Export *.TXT Coordinates 24
- Backup / Restore Job 26
- Backup / Restore – Backup 28
- Backup / Restore 29
- Create a Snapshot 29
- Backup / Restore – Restore 29
- Transfer 30
- Register Modules 31
- About Survey Pro 32
- Job Menu 33
- Settings 34
- NOTICE: 36
- Units Settings 37
- Format Settings 38
- Files Settings 39
- Surveying Settings 40
- Stakeout Settings 41
- : When checked during 41
- Repetition Settings 44
- Date/Time Settings 45
- Buttons Settings 46
- General Settings 47
- Edit Points 49
- Edit Point – General 51
- Point Feature Attributes 52
- Edit Point – Location 52
- Edit Polylines 53
- Screen Four – Add/Edit Curve 55
- Adding a Spiral 56
- Adding a Vertical Curve 56
- Edit Alignment 58
- Edit Segment – Spiral Card 63
- Auto Linework 65
- View Raw Data File 69
- View DTM 70
- Layers for Staking DTM 71
- Choose Polyline 72
- Add/Edit Break-lines 72
- Edit Polyline 73
- Points on DTM Layer 74
- 3D View 75
- 3D View Settings 76
- Manage Layers 77
- Job Information 78
- Calculator 79
- Survey Menu 83
- Backsight Setup 84
- Check Backsight Dialog Box 85
- Check by Distance Results 86
- Check by Angle Results 86
- Backsight Circle Dialog Box 86
- Traverse / Sideshot 87
- New Occupy Point Dialog Box 89
- Point Exists Screen 90
- Repetition Shots 92
- Multiple Sideshots 94
- 1_ft back 95
- 3_ft right 95
- Horizontal Angle Offset 96
- Vertical Angle Offset 97
- Auto Collect 98
- Auto Collect – Screen Two 99
- Corner & 2 Lines 100
- Corner & Angle 101
- Corner & Offset 102
- Corner & Plane 103
- Shoot From Two Ends 104
- Record Mode 105
- Resection 106
- Save Point Screen 107
- Resection – Screen Two 107
- Results 108
- Remote Elevation 109
- Solar Observation 110
- The Enter Shot Data Screen 113
- Sun Shot Procedure Summary 113
- Remote Control 115
- Turn To 116
- Stakeout Menu 117
- Stake Points 118
- Stake Points – Screen Two 119
- Stake Points – Screen Three 120
- Remote Staking 122
- Stake List of Points Screen 123
- Edit Point List 124
- Stake to Line 125
- Stake to Line – Screen Two 126
- Remote Stake to Line 127
- Offset Staking 129
- Offset Staking – Screen Four 132
- Slope Staking 134
- Slope Staking – Screen Three 135
- Slope Staking – Screen Four 136
- Slope Staking – Screen Five 138
- Slope Staking Offset Stake 139
- Stake Line and Offset 140
- value increases 141
- screen, described 141
- screen, which is 142
- Screen Summary 142
- Stake Curve and Offset 143
- on the left (while 144
- Stake Spiral and Offset 147
- on the left (while viewing 148
- Summary 150
- Show Station and Offset 151
- Store Offset Points 153
- Stake DTM 156
- Select Line 158
- DTM Shot 159
- information for the rod 160
- Define a Location 161
- Where is Next Point 163
- Inverse Menu 165
- Inverse Point to Point 166
- Inverse Point to Line 167
- Inverse Point to Polyline 168
- : indicates if the 169
- Inverse Point to Multiple 170
- Inverse Point to Location / 171
- Cogo Menu 173
- Point in Direction 174
- Intersection 175
- Offset Line 176
- Offset Points 177
- Corner Angle 179
- Compute Area 180
- Triangle Solutions 181
- Map Check 182
- Add / Edit Line 183
- Add / Edit Curve 183
- Add to Map 184
- Hinge Method 185
- Parallel Method 185
- HD/VD to SD/ZA 187
- SD/ZA to HD/VD 188
- Curve Menu 189
- Curve Solution 190
- Results: 191
- Known PI and Tangents 192
- Three Point Curve 193
- Compute Radius Point 195
- Line Tangent to Circles 197
- Horizontal Curve Layout 198
- Tan Dist 199
- Chord Dist 200
- Traverse on Curve 202
- Parabolic Curve 204
- Parabolic Layout 206
- Straight Grade 208
- Spiral Layout 210
- Traverse on Spiral 211
- Roads Menu 213
- Add/Edit Templates 214
- Edit Template 215
- Edit Segment 216
- Slope / V Offset 216
- Edit Alignments 217
- Add/Edit Roads 217
- New Road Screen / Edit Road 218
- The Road Card 219
- Roads Report Screen 219
- Road Profiles Screen 221
- The Templates Card 222
- Add / Edit Template Screen 223
- The Widenings Card 224
- Add / Edit Widening Screen 225
- Super Elevations Card 226
- Road Stakeout 229
- Stake Road – Screen Three 231
- Stake Road – Screen Four 232
- Road Slope Staking 233
- H. Map Card 234
- V. Map Card 235
- Slopes Card 235
- Fill Hinge Points Card 235
- Road Station and Offset 236
- Alignment Card 237
- Cross-Section Card 238
- Shot Data Card 238
- Adjust Menu 239
- Translate 241
- Traverse Adjust 243
- Traverse Adjust – Results 247
- Miscellaneous Screens 249
- Create Points Screen 250
- Map Display Options 251
- Map View 252
- Appendix A 253
- Lambert Zones 254
- ..........156, R-194 257
- ...160, R-137 257
- ...................156 257
- ...............156 257
- R-170, R-171 259
- .......................128 259
- ...........R-141 260
- .R-137 260
- ....R-134 260
- ...................R-123 260
- .........R-145 261
- ........R-147 261
- .......156, R-193 261
Relacionado con productos y manuales para Software Spectra-precision Survey Pro v3.80 Recon iPAQ Reference Manual
(93 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales