Spectra-precision Survey Pro 3.80 Recon GPS Reference Manual Manual de usuario

SURVEY PRO for Recon GPS Reference Manual 2003 Tripod Data Systems, Inc. All Rights Reserved

GPS Reference Manual 10 Auto Accept: is where you select to use criteria for automatic point acceptance. When checked, both the data and Offset Shot

Job Menu 11 Post Process Settings The Post Process card is used to configure the post processing raw data storage settings. Recording Interval: is

GPS Reference Manual 12 Note: This function only works during post processing data collection using the session screen. For status during simultane

Job Menu 13 : opens the Receiver Communications screen, where many of the displayed communications settings can be changed. Receiver Communication Sc

GPS Reference Manual 14 : sets all the fields to the default values. : sets the baud rate on the chosen receiver port to the selected value. Note: T

Job Menu 15 : establishes communication with the radio firmware and opens the Radio Settings screen (Page R-15), where you can change the radio chann

GPS Reference Manual 16 However, not all radios support all of the described settings, so if you do not see one of these fields, it is because the ra

Job Menu 17 Rover Modem Settings The Rover Modem Settings card is used to view and configure the settings for the modem used with the rover

GPS Reference Manual 18 RTK Configurations The RTK Configurations Settings card is used to configure automatic connection when RTK base an

19 Survey Menu – RTK The Survey Menu contains the routines used for collecting data. The screens below are available only when running Survey Pro in

ii TRIPOD DATA SYSTEMS SOFTWARE LICENSE AGREEMENT IMPORTANT: BY OPENING THE SEALED MEDIA PACKAGE, YOU ARE AGREEING TO BE BOUND BY THE TERMS AND CONDI

GPS Reference Manual 20 GPS Status The GPS Status screen contains several index card-format screens providing information about the current GPS s

Survey Menu – RTK 21 • Code: we are receiving a code differential solution (precision is about 1 to 10 meters). • Float: we are receiving a carrier p

GPS Reference Manual 22 Data Link The Data Link card displays information about the radio communications. Receiver mode: (see the Receiver Status car

Survey Menu – RTK 23 Sat Info The Sat Info card displays signal quality information for the satellites that are being used and allows you to disable

GPS Reference Manual 24 Position The Position card displays your current position as well as your course and speed information if you are moving. Pos

Survey Menu – RTK 25 Base Setup The Base Setup screen is used to set the base point in Survey Pro and to configure the receiver to begin broadcas

GPS Reference Manual 26 Base Setup One – Pick Base Point The first Base Setup screen is used to pick the base point and set the antenna height. Base

Survey Menu – RTK 27 • If the base point does not have geodetic coordinates or if geodetic coordinates cannot be computed for this point, the final s

GPS Reference Manual 28 Base Setup Two – GET and SET This final Base Setup screen is used to GET an autonomous (here) position from the receiver and

Survey Menu – RTK 29 Phase CenterRadiusSlant OffsetVertical OffsetMeasurementPointMarkerVerticalHeightSlantHeightyou do this, each setup is assigned

iii Table of Contents Settings...R-6 Receiver Settings...

GPS Reference Manual 30 Note: If your antenna type is Manual, the Radius and Notch fields will not be available : Updates the base antenna settings

Survey Menu – RTK 31 this data collector. This function configures the rover with the displayed geodetic coordinate. Last Antenna for this Receiver:

GPS Reference Manual 32 Control Points The Control Points screen is used to measure or check control points in the projection solution. GPS Statu

Survey Menu – RTK 33 Manual Entry GPS The Manual GPS screen allows you to manually enter geodetic coordinates from the Control Points and Ch

GPS Reference Manual 34 Errors: displays the differences between the computed local coordinates and the known coordinates for the control point. Note

Survey Menu – RTK 35 Occupy Control Point Screen The Occupy Control Point screen is used to add geodetic coordinates for a known project point

GPS Reference Manual 36 Data Collection The Data Collection screen is used to collect new points for the current job. GPS Status: displays the cu

Survey Menu – RTK 37 Feature Collection Screen The Feature Collection screen is used to partially automate the process of data collection. It

GPS Reference Manual 38 Interval: is where you enter the interval criteria used for continuous collection modes. The Interval field is not available

Survey Menu – RTK 39 : is used to occupy the GPS reference point. A prompt for the name of the GPS reference point is followed by the Occupy Data Po

iv Line and Offset...R-88 Curve and Offset...

GPS Reference Manual 40 : returns you to the previous screen, and depending on which screen was used to open the Occupy Data Points screen, will usua

Survey Menu – RTK 41 Mapping Plane The Horizontal tab of the Projection screen is explained below for when the horizontal projection type is set t

GPS Reference Manual 42 : opens the Solve Localization screen, where the control points can be selected and the horizontal and vertical localization

Survey Menu – RTK 43 Note: This delete function cannot be undone. Also, you cannot delete system database records. If you select a protected record

GPS Reference Manual 44 • North Azimuth: is where you set a north azimuth for your new zone. • South Azimuth: is where you set a south azimuth for yo

Survey Menu – RTK 45 Projection Key In Setup - Oblique Mercator This page is only displayed when the Zone type is set to Oblique Mercator Angle. Azi

GPS Reference Manual 46 Projection Key In Setup - Datum Translations Choose an ellipse for the new zone. • Ellipse from List: choose this option to

Survey Menu – RTK 47 Projection Key In Setup - Datum Rotations and Scale The following screen is only displayed when Datum type is Similarity. Datum

GPS Reference Manual 48 Ground - TDS Localization The Horizontal tab of the Projection screen is explained below for when the horizontal projection t

Survey Menu – RTK 49 Localization Projection Setup The Localization Projection Setup screen is used to manually configure the parameters of the

5 Job Menu A: Settings B: New C: Open D: Edit Points E: Edit Polylines F: Edit Alignments G: Auto Linework H: Save As I: Import Coordinates J: Export

GPS Reference Manual 50 Localization Data Base The Localization Data Base screen is used to pick a localization reference stereographic map pr

Survey Menu – RTK 51 Solve Localization – Control Points The Solve Localization screen is used to pick control points for a least squares loca

GPS Reference Manual 52 : opens the manual entry screens in Localization Calculator mode. This interface, only available when using Ground – TDS Loc

Survey Menu – RTK 53 Solve Localization – Manual Parameters Horizontal Card The Horizontal card is used to manually enter the six parameters o

GPS Reference Manual 54 Localization Calculator This sub section describes a feature available only in Ground – TDS Localization mode.The Local

Survey Menu – RTK 55 : computes the horizontal localization parameters using the entered scale, rotation, and base station local coordinates. Locali

GPS Reference Manual 56 Localization Calculator – Rotation – Details Projection: displays the current mapping plane selected. : calculates the rotati

Survey Menu – RTK 57 Solve Localization – Results or or Horizontal Card The Horizontal card shows results of the horizontal localization

GPS Reference Manual 58 Vertical Card The Vertical card shows results of the vertical localization solution. Status: displays the status of the curre

Survey Menu – RTK 59 Vertical Card The Vertical card displays information about the currently selected horizontal projection method. If the sel

GPS Reference Manual 6 Settings The Settings screen opens several individual screens that control all hardware and software settings. The screens

GPS Reference Manual 60 : opens the Geoid Model Setup screen, where you can select a geoid to use with the current zone, change the geoid file of the

Survey Menu – RTK 61 Ellipsoid Height The Vertical tab of the Projection screen is explained below for when the vertical projection type is set to El

GPS Reference Manual 62 Remote Elevation The Remote Elevation screen is used to compute and store a new base point elevation and vertical site by o

Survey Menu – RTK 63 elevation coordinate. When the horizontal projection is not solved, and the dialog is used only to occupy a vertical control po

GPS Reference Manual 64 Receiver Recording The Receiver Recording screen is used to start or stop the receiver recording. When in RTK mode, it all

Survey Menu – RTK 65 Measured: is where you enter the height of the antenna, measured to the location specified on the Post Processing Antenna screen

GPS Reference Manual 66 Readjust Points The Readjust Points screen is used to readjust selected points with the latest projection settings. The ho

Survey Menu – RTK 67 Readjust Points: Plane to Geodetic – Screen Two Points Selected: displays the number of points selected. : calculates the differ

GPS Reference Manual 68 Readjust Points – Recalculate Results Displays the number of points that were adjusted and if any points were not adjusted, a

Survey Menu – RTK 69 Projection Calculator – Rotation Convergence: displays the computed rotation from geodetic north to grid north. Rotation: displa

Job Menu 7 Receiver Settings The Receiver Settings card is used to select the GPS receiver make and model as well as the mode of differential dat

GPS Reference Manual 70 Projection Calculator – Scale Mapping Plane Scale Factor: displays the computed mapping plane scale factor on the selected ma

71 Survey Menu – Post Processing The Survey Menu contains the routines used for collecting data. The screens below are available only when running Su

GPS Reference Manual 72 GPS Status The GPS Status screen contains most of the same index card-format screens as the RTK Status case. When in Post

Survey Menu – Post Processing 73 Remaining: displays the time remaining in the current session if a session is in progress. If your receiver does no

GPS Reference Manual 74 Mem. Threshold: displays the memory threshold set on the Post Process card of the Job, Settings screen. SV Threshold: the sat

Survey Menu – Post Processing 75 Start Stop/Go Rx The Stop/Go Rx Recording screen is used to start or stop recording in a stop and go receiver’s in

GPS Reference Manual 76 Data Collection The Data Collection menu opens the Receiver Session screen. The Receiver Session screen is also opened aft

Survey Menu – Post Processing 77 Description: is where you enter the description for the next static session or stop and go point. Log Until Stop: i

79 Stakeout Menu The Stakeout Menu contains the routines used to stake existing points and other known locations. A: Stake Points B: Polyline Points

GPS Reference Manual 8 Measure Mode Settings The Measure Mode card is used to configure the RTK data collection settings. Receiver Dynamics: is wh

GPS Reference Manual 80 Stake Points The Stake Points screen in used to locate and stake out points in the field from coordinates in the job file.

Stakeout Menu 81 Rover is greater than 3 m (10 ft) from the design point. Rover is between 0.3 and 3 m (1 and 10 ft), from the design point. Rover

GPS Reference Manual 82 Note: When Store GPS Raw Data on the Job/ Settings/ Measure Mode card (Page R-8) is set to + Rx. Raw (and / or +OBN for Ashte

Stakeout Menu 83 Stake to Line – Screen Two The second screen is where measurements take place and the staking directions are displayed. The graphic

GPS Reference Manual 84 Go EAST / WEST: displays the distance the rover must move in an east or west direction to reach the closest point on the line

Stakeout Menu 85 / : toggles the display between Results and Current Location. : prompts you for a point name and description and stores a point fo

GPS Reference Manual 86 Slope Staking – Screen Four The graphic portion of the Horizontal Map and Vertical Map is updated continuously. This allows

Stakeout Menu 87 • : forces all computations to be based on a fill slope. The second button selects which information is displayed in the lower corne

GPS Reference Manual 88 Toward CL / Away CL: is the computed horizontal distance that the rod must move either toward the centerline or away from it,

Stakeout Menu 89 Curve and Offset The instructions for the Curve and Offset routine for GPS are similar to the conventional method, except that the

Job Menu 9 Note: All receivers need to be in static mode to record Rx. Raw, and some receivers always record Rx. Raw when in static mode. If the co

GPS Reference Manual 90 Show Station and Offset The Show Station and Offset routine allows you to position the rover anywhere near a polyline, a ra

Stakeout Menu 91 Note: When Store GPS Raw Data on the Job | Settings | Measure Mode card (Page R-8) is set to + Rx. Raw (and/or +OBN for Ashtech) swi

GPS Reference Manual 92 Stake DTM The Stake DTM routine allows you to stake an area and get cut / fill and volume information based on a referenc

Stakeout Menu 93 Note: When Store GPS Raw Data on the Job/ Settings/ Measure Mode card (Page R-8) is set to + Rx. Raw (and / or +OBN for Ashtech) swi

GPS Reference Manual 94 C.L.: shows the current station and offset information for the rover location relative to the selected centerline. The type

Stakeout Menu 95 Inverse Menu All of the routines available from the Inverse Menu are identical to those explained in the conventional Reference Manu

Index A adjust horizontal / vertical62, 63 antenna height ...R-74 ASCII...69, 70 auto detect ...

HARN...5 horizontal datums ...4 HARN ...5 NAD27...4

Index rover radio card...R-17 RTK config card ...R-18 remote elevation...28, R-62 rotation.......49, 50 rover recei